Powering up your DigiProg III-User manual For Newbie

A regulated 12 volt power supply should be used to power your DigiProg III. If anything above 13.5 volts is used to power the machine,
damage may be caused to the main circuit board and it will need to be sent to your DigiProg dealer for repair.
When connected to a vehicle by OBD DO NOT use the cigar lighter lead, the Digi takes power from the vehicle. Failure to observe will result in
damage not covered by the warranty.
When your DigiProg is powered up, this screen will be displayed whilst your machine is loading:

On this screen your DigiProg’s status/software version is displayed along with your machines unique 12 digit electronic serial number.
When your DigiProg has finished loading an information screen will appear with a disclaimer regarding the use of the machine. When you
are ready, press the check/tick button.

The DigiProg will then ask for a password to be entered before the machine can be used. The default password is set to 1 but can be
changed in the SETUP function
Main menu screen

1. EEPROM menu
The first option on the main menu is the Eeprom menu. Reading,writing and saving Eeprom information is all done using this menu.
A more detailed guide to using this menu follows later on in the introduction.
2. CAR/TRUCK menu
This is the menu you will use for correcting and reprogramming vehicles. Manufacturers are set out in alphabetical order and models of vehicles are set out in a simple sub-menu format.
3. Motorcycle Menu
This menu is the same as the CAR/TRUCK menu but is used for reprogramming motorcycles.
4. Special Functions Menu
The special functions menu is for use only by official DigiProg dealers.
5. Setup Menu
This menu is where settings on your DigiProg can be changed. Language, password, brightness, volume, and the time/date can all be set and changed in this menu. You can also change whether your machine is working in kilometres or miles.
Using the EEPROM menu.
On some of the vehicles you will come across, an eight pin Eeprom chip will be used to store the vehicle data. These chips hold vital information from the vehicle such as ignition and immobiliser codes. Loss of this information could result in anything from minor faults, to major faults involving the vehicle not starting and having to be taken to the main dealer. This is why it is very important to read and save the original information from the Eeprom before programming, this way if any errors do occur you can always return to the point you started.

The process of reading and saving this information is very simple. The Eeprom chip itself will have a mask number printed across the
top of it, for example a widely used chip is a 93C46.You can connect the chip to your DigiProg by using adaptor ST1 or ST4. Most chips are surface mount eeproms which will use ST1,but the larger DIL chips will use ST4.
You must then tell your DigiProg which chip you are working on before you read it. To do this you must press the EEPROM button at
the top of the screen. A sub-menu will now appear.

Select the SET TYPE button and choose 93C46. Your DigiProg is now set up to read a 93C46 chip. Press EEPROM again, this time
selecting the READ button. Once the machine has finished reading the chip, the information will be displayed on the DigiProg screen,
now press VERIFY this will ensure that the information on your screen agrees with the Eeprom.

Now you have the original data file from the vehicle you must save it to the DigiProg III.

Press the FILE button in the top right corner of your screen.Another sub-menu will appear. When you press the SAVE button
the machine will now ask you to enter a file name for the information you are saving. Once a file name is entered your data is safe and the vehicle is now ready to be reprogrammed, you can only use 0 to 9 & A to F for file names but you can save them to
your PC in Eetool which is supplied with your DigiProg as any name. I would suggest you create a folder in My Documents & call it
Eetool Data Files, then create sub folders in the folder for example Audi, Alfa, Etc.
Please if you are stuck use the help desks on ICQ 178 762 503 or MSN Digiprog, please read your instruction manual before using the
help desk almost all help desk enquiries can be dealt with if you READ the manual.
Finally some important points to remember. Always connect the Eeprom to the ST01 or ST04 before you
connect to the DigiProg this will avoid Electro static feedback
(ESD).
Never solder the connections whilst the lead is connected to the programmer, this will damage the DigiProg.
Please do not sit at home or in your car & play with the DigiProg to see which cars it can do. If you press the DigiProg function keys the
DigiProg will start looking for the Cars protocol, you wouldn’t ask your PC to print if there was no printer.
Always keep your DigiProg in its case when not in Use & keep it in a dry environment at night (don’t leave it in the trunk of your car)
If you are using solvents to remove lacquers’ from Eeprom’s ensure that they are cleaned completely as the solvent can damage the
clips.We hope you will have many years of use from your DigiProg, don’t forget if you are not sure ask the helpdesk.
http://www.mileageprogrammer.com/powering-up-your-digiprog-iii/

Digimaster 3: IC Soldering

Video demo:Digimaster 3: IC Soldering

How To Solve Digimaster 3 CD Card lost?

Customer question:
i lost my CD card in digimaster3,could we install the digimaster 3 software?
Answer from OBDexpress.co.uk:
1.Preparations, you could buy a new blank SD card within 8GB.
2.Go to the YANHUA TECH official website to donwload software:
http://iccdp.com/download/page.do?page=3

3.After software downlods,you should unzip the software file first ,copy it to the new SD card,there is an operation instruction in the file package, follow the instructions to synchronize the SD card program.

Add other Customer asked questions:
Q: Digimaster 3 and digiprog 3 are both odometer correction tools, can you tell me the difference. Digimaster 3 is so expensive, i want to know it better.
A: Digimaster 3 has the main function of digiprog 3, but the car models they support are different. Such as Didiprog 3 support Benz/BMW/Porsch key programming function, while digimaster support more car models for airbag reseting function. The relationship of the supported car models is not coverage, but complementary. Digiprog 3 has 8 kind of language to choose, while Didiprog 3 only has English language.
Q: How to update it?
A: Our digimaster 3 is updated online. You can follow our user update manual to update on the website.
Q: I see the tokens on your website, it adds some car models, do i must buy it?
A: The product you mean Item number SS65. If you want to do more and newer car models, then you can buy it. If you just want to do the car models on the attached files, then just buy this product is ok.
Q: Do i need to register it first after i get it, or before i use it to work on cars?
A: This one needs register. But we will register it ready before we send it to you. Once you get it, you can use it directly.
Q: Does it need user name and password? I need to update it, please tell me it.
A: This one does not need user name and password. Ignore it and go official website to update it.
Q: When i use it, i do not find my car list, does it mean it cannot work on my car?
A: No. You can use it based on the chip. There is the chip list on the main unit. You can change the mileage based on the chip.
Q: Can i use it to change the motocycle models?
A: Yes.
Q: I'm trying to change odometer in bmw e46 2005 by obd with vw audi adaptor lead as stated on screen instructions but it says device not found?
A: You use the wrong way to change the odometer. Because this one is not directly change the mileage via OBD. When you use this digimaster 3, there is the prompt on the screen, see this prompt. You need to remove the chip. On the screen, it will prompt you where is the chip on dashboard. Follow the prompt to remove the chip, then follow the prompt to choose the right cable to connect the chip with digimaster 3.


Enjoy!

More Digimaster III odometer correction Tech support at here：
http://www.mileageprogrammer.com/category/digimaster-3/

Digiprog 3 Odometer Correction Doesn't Models List

Here,OBDexpress.co.uk has collected Digiprog 3 test/feedback on the web,people usually post Digiprog 3 success,But for those who are looking for a DP 3 for personal use, they should confirm if their car works or not. If not, Digiprog 3 is nothing for them. Here is the car list with no luck.
Digiprog 3 Cars – NOT OK
vw beetle 2013.
digiprog obd not ok.
(then try x-tool, also not ok. must change manually, soldering)
I did 2009 MB W212 and worked fine.
But now i wanted to do another w212, it reads something wrong- 2 million something… but odometer shows 350000. And cant change it.
Mini Cooper R50:
no possible.
use rosfar r260 for dash
mercedes w221 2007 cluster ok assyst ok
mercedes w164 2006 cluter ok assyst ok
astra 2010 cluster ok
bmw e60 cas by cluster plug km changed in wrong adress and red dot on cluster remain !!!
corsa c ecu eeprom direct not work
space star 2002 eeprom pointers dont work after !!!
ford connect 2002 with 912 with cable 48/2 cluster dead mcu not readable even with etl !!!
What you mean bmw e60 cluster plug?
You mean you did cas try dash plug
Cable 62 and you have dot.
Dot will desapere after 19 km.
with dp3 cas 3+ work try obd with out any problem.
cas2 with dp3 dont work i try like 11 cars no luck
e65 with dp3 obd dont work.
Freelander 2 2008 wrong calculation
the only one not on is Audi A1
jeep cherokie 2004 908as60 plug 42 not work
VW polo 2005 dash VDO not work
Audi A6 2003 dash not work
Audi A6 2005 dash work( test only if is read i not change it)
VW T5 EDC16 read km ok by OBD,write … but km still not change,i removed ECU and mod eeprom
vw lupo 2002 with rb 4 dash not ok
get message “unknown version rb4”
try old 912 bsi 307 with this tool and now bsi dead
fiat punto 2000 read good milleage when programming is finished it says verify new milleage but milleage still the
same
Tested on Audi A4 EDC16, not working.
Ibiza 2007 dash MM with 912h256 inside, can’t do by OBD
MERCEDES A-CLAS – 2000 OBD NOT OK
Tested on W212 ecu year 2010 commender not read
W211 ZGW not work
dash eeprom 95020 citroen berlingo 2012 dont work “unknown version
FIAT PUNTO 2008 OBD not work
Mercedes CLK W209 from 2003 did not work by obd.
Evo no
C-Max 2005 with 590k km both digiprog and carpog 4.01 sing – “Unknown version”.
Focus (old shape) not good just checked cable and the massa is on the wrong pin after that i did not check anymore.
2004 Touran 1.9 tdi ecu km… not working, dash is ok. On ecu reads Km ok after writing new km value still old km
displayed
touran 2004 is edc16, do it manually
A6 ,4G, 2011 obd ,no success
read old km not corect
MB CLC 2009 dash plug don’t work …
Ford Fiesta 2002 via obd not work
Ford F150 2002 with HC11… N O N E S !!!! wasted time… Not working… After try connection show E R R O R !!!
F150 2002 i have do 2 weeks ago with digiprogclone and works fine. have you make wrong job
Opel Astra 2.0 DTI from 2001 with VDO, and when I try to connect with OBD cable, screen shows “unknown version
vw polo 2012 didnt work
i have make Polo 5.2012 and work
Chev Kalos / Aveo HC08 does not work on “Clone”
HC08 not work on any dash ….
tested on many
Hi guys 908 work fine on mine done many I guess you just need to know how to work it !!! Take note most of the leads
that come with it are either poor quality or wired wrong
not work with golf 6 2011 Nec 24c64
Today do Golf6 2011 Dash MM read old value ok and write ok, But dash now say: Error and not show value
Try different value and double check which version of dash is
Yes, this car work whitout dash
Q5 2012 don’t work
EWS3 don’t work
Ford Escape 2007, no work obd2, cable 16
error unknown dashboard
corsac obd OK
ford fokus 2002,read old km—-not write new km
opel insignia obd ——-not comunicate
Cable ford focus not ok.
Check with scheme or compare with other programmer.
2006 Ford fusion obd- not work
2006 VW Jettta – dash read wrong mileage (34,xxx miles )
ecu – unknown version
dsg- read wrong mileage ( 22,xxx miles)
Btw for Plug 1 am I suppose to have a eeprom clip ? I just have the board that says 01/04.
Mercedes c200 cable 8/9 no works
cas plug 35pin(black) to digi 10pin
cas plug 34pin(green-red) to digi 25pin
cas plug 26(yellow) to digi 9pin
cas plug 12(braun-black) to digi 13pin
for 48/2 i think this:
brown pin 13 gnd
white pin 7 +5v
green pin 17 Reset
yellow pin 18 BCKND
work on 307bsi,no work on rexton dash(did with carprog).more not tested.
most EDC15-16 not working…
2005 EDC16 and did not work…
dp3 and smok and smelecom and diag tool to clear error but no joy.
after spend couple days trying this and that i have extract the flash repair it and then all problem was gone.
on this forum also other members had the same problem with volvo’s using clone digiprog.
it damage the flash!
jeep cherokie 2004 908as60 plug 42 not work
dont work at all, I try with two models of boards
Megan 3 ABS, work only with ESP unit ,without ESP not work via epprom
Smart BSI / BCU 2002 No picutre to try it, plug of my DP3 is not the same as on my picutre
Volvo XC 60 from December 2011 NOT POSSIBLE by OBD, it read 2.453.987.567 Kilometers (real 162.987), writing take about 10 minutes, but without effect.
VW Caddy 2009 year wth DSG via OBD tacho and ECU – ok
DSG only reset I donn’t write new odo I don’t write DSG reset to 0 km – tell me it is ok , or 0 km to DSG can do problem by later ( I don’t now bloked gear examply or other problem ) or mayby 0 km in DSG is ok, advice my mate please
I work with digiprog 3 ver V4.94 with VW caddy 2009 year
Good luck!
Source:http://www.mileageprogrammer.com/digiprog-3-odometer-correction-failed-models-list/

How to use Digiprog 3 clone for Ferrari 458 odometer correction

Tips and Guides: clone Digiprog 3 Ferrari 458 mileage correction

Possible to change km on Ferrari using Digiprog 3 clone?
I've done a 2010 458 by obd with digiprog.
2min. Done. Perfect
If it reads the correct old mileage you're good to go

Will try 458 with Digiprog 3. Your thoughts?
Once did a 458 with Digiprog 3.
Someone doubt that DP3 can do this. But for me, it works! Though it is a clone, but the software is same as original tool.
The tools only needs to read the EEPROM, we know Digiprog can do this for many other cars without problem, so if it reads the correct mileage so I don’t see much risk.
But the mileage is also in the ECU of Ferrari.

Anyone got experience of China clone Digiprog on Ferrari?
Yes. I did it. Did a Ferrari California with Digiprog 3 in 2min OBD



Which version of digiprog3 did you use? I don't see a selection for Ferrari 458
it was no problem when using digiprog 4.94.
all good.
express bought the tool instead of removing dash. better

Digiprog says it can do over obd, but i have a hard time to believe it does 2012 Ferrari 458. Any professional or official can help confirm this?
Look here:

source: http://www.obdexpress.co.uk/wholesale/main-unit-digiprog3-iii-digiprog-3-odometer-programmer.html
Confirmed! Digiprog 3 Ferrari 458 is supported since version 4.88!

Src:http://www.mileageprogrammer.com/digiprog-3-clone-ferrari-458-odometer-correction/

How to use Digiprog 3 clone for 2012 Golf 6 odometer correction?

 Topic:2012 Golf 6 mileage change


Tools option:Digiprog 3 clone


Step-by-step guide below here:




the current mileage: 212099km

connect Digiprog 3 to the car via OBD

then the machine starts

select a car: VW-Golf-Golf 6-Tacho Diag 2012

DP3 is reading the current mileage

Golf 6 mileage is read out

it’s 212128km, almost the same as what displayed on the dashboard

enter a new mileage to change

new mileage: 200000km

the mileage on the dash is also changed!

Digiprog 3 china clone is confirmed to OBD change km for Golf6!

Works perfect!

Src:http://www.mileageprogrammer.com/digiprog-3-clone-golf-6-2012-odometer-correction/

Tips and Guides: BMW Mlieage Adjustment Programmer

For how to choose a bmw mileage correction tool/software of high quality at a good price.You have 2 options, 1 buy a speefilter OEM from us if the car is new, your client can control EVERY ECU km from day 1 with pressing a button on the steering wheel, second if your looking to make COMPLETE fix on bmws you'll need more than 1 tool
1)You'll need a tool like Digiprog 3 or something to do dashes
2)You'll need something to do cas units, depending if you want to do obd2 or remove them
3)You'll need cleaner software that can clean every ECU out of ANY model BMW, all 12-15 ecu's per car and every km record, even DME/DDE
The one thing that I have only seen on 1 tool is the removal of all 4 cas3/3+ history KM's, thats right its not just 1 KM that needs to be changed with all these hi end tools as well, there are aside from the main one inside eeprom, which syncs with dash and keys, there are 3 HISTORY KM's that the unit stores as well.
Digimaster 3 for odo and R280, R270 for cas, newer models (Fxx) need canfilter!

FVDI clone not good!
ALL MODULES CAN BE DONE, and OVER OBD2 very easily in fact. That’s number 1, number 2 Fxx do not need canfilters, if you need to repair the km if there too far to use a speedfilter to stop km you can do like me, change our cas4 unit completely with one that is ordered for the car's vin, do the dash and they will sync. Then use sw to do all the other ecus
Digimaster 3 is the best mileage correction tool for BMW CAS 2000-2017.
Share a 2000-2016 BMW CAS models list on mileage correction and key programming, follow the list, you can check the corresponding CAS modules.

Digimaster3 BMW Car List (2000-2017 )
BMW Car Model	CAS1 912DG128 (3K91D)	CAS2 9S12DG256 (2K79X)	CAS3 9S12DG256 (0L01Y)	CAS3+ 9S12XDP512 (0L15Y)	CAS4 9S12XDP512 (1L15Y) 9S12XEP100 (5M48H)	FEM
BMW 1 Series		2004-2006 (E87)	2007(E87)	2008-2011 (E87)		2012-2014 (F20)
BMW 3 Series		2005-2006 (E90)	2007(E90)	2008-2012 (E90)		2013-2014 （F30/F35）
BMW 5 Series		2004-2006 (E60)	2007(E60)	2008-2010 (E60)	2010-2014 （F07/F10/F11/F18）	Not available yet
BMW 6 Series		2004-2007 (E63/E64)	2008(E63/E64)	2009-2010 (E63/E64)	2011-2013 (F12/F13)	Not available yet
BMW 7 Series	2001-2004 (E65)	2004-2008 (E66)			2009-2013 (F01/F02)	Not available yet
BMW X1 Series				2010-2014 (E84)		Not available yet
BMW X3 Series					2011-2013 (F25）	Not available yet
BMW X5 Series			2007(E70)	2008-2013 (E70)		2014（F15）
BMW X6 Series				2008-2014 (E71)	Not available yet	Not available yet
BMW Z4 Series				2010-2013 (E89)	Not available yet	Not available yet

Digiprog 3 vs. Digimaster 3
Both Digi3 and Digimaster should do the job. Digi3 is cheap and good, Digimaster is more like a professional tool, and of course costs much more.
bmw f30 mileage correction:
Credit: http://mhhauto.com/Thread-Odometer-in-BMW-F30-with-FEM
R270+ programmer should be able to do the dash on f30 
in dash you have QD160. and if you put filter in FEM tell you customer
that when he go with car to dealer and they read out the mileage from the key
that they will read the Original mileage still. and if the car has tele option then they can see
on computer the Original mileage in house.
To do the key...
If he got new fem from dealer coded to car it comes with 0km, if he makes dash xxxxx fem will take km from dash. Once both are synced with same km, he takes each key 1x1 and drives 15-20km and key will take new mileage. After that using bmw explorer or bmw cleaner he should clean all the other ecus to 0. If hes smart he'll put in a speed filter after this if the car is going to stay on the road

Src:http://www.mileageprogrammer.com/bmw-odometer-correction-tool-buying-guide/

How To Use Digiprog III Change 2006 Audi A6 4F Mileage Via OBD

Here is how to use Digiprog III to do mileage correction on 2006 Audi  A6 4F via Carprog v8.21 Firmware Perfect Online Version with All 21 Adapter step by step.
Video:







DONE!
Src:http://www.mileageprogrammer.com/digiprog-iii-change-2006-audi-a6-4f-mileage/

Odometer correction tool: Digiprog 3? Digimaster 3?

Odometer correction tool Digiprog 3 or Digimaster 3,how to choose?

Here you go. Digiprog 3 vs. Digimaster 3

Analysis from the official:

Product	Digiprog 3	Digimaster 3
Image
Original/clone	Cloned	Original from Yanhua
Software	V4.94 Not able to update	V1.8.1707.21Update all the time
Screen Size	Smaller	Bigger
Language Supported	English, Espanol, French, Deutsch,Portuguese, Italiano, Turkish, Dutch	English
Way to change mileage	By OBD2 or dashboard or Chip	By OBD2 or dashboard or Chip
Update	Users are not allowed to update sw by themselves. (Need to update sw by email or send the main unit back to update.)	Original and update online by users anywhere anytime, and it’s free to update for the first year.
Vehicle list	For universal car, but cover less vehicle models than digimaster 3. Cannot do well For Ford, For Benz, BMW, Opel , digimaster 3 can do.	The best odometer tool for universal cars (incl. high-end cars), such as Ford, BMW, Toyota, Benz, VW, Audi,Volvo,Renault,Peugeot and high-end cars.
Vehicle year	Covers vehicles from 1996 to 2013 (some can do 2014 year); Not works for new cars in the future	Covers vehicles from 1996-2017; Good for new cars and future cars
Tokens	No tokens limited	Item No.SP78 no token limitation; Item No.SP78-B with 1080 Tokens
Function	Mainly for setting and programming digital speedometer.	odometer correction, Audio decoding, airbag resetting, engine ECU resetting, IMMO, programming key for Benz &BMW etc
Difference	Digiprog 3 is good for odometer correction for most universal vehicles. But for the new and high-end cars or new cars, you need have a Digimaster 3. If you want to choose one multi-function mileage correction, Digimaster 3 is the best choice.it contains the advanced technology of programming new keys for BMW and Benz, CAS-BDM reading/writing and resetting; 35080V6 erasure etc.

Customer feedback: Digiprog 3 vs. Digimaster 3

Feedback 1:
I think digimaster is not worth the money (only if you do BMW). can do more digiprog, and often need to desolder.
digiprog can do a lot of cars. even mercedes 2010 by obd.
Best is to buy Yanhua digiprog if you can find them (its better quality).
The cheap digiprog from alipress often stop working. sometimes right out of the box, sometimes after 2 years.
If you're thinking about spending 1500 euro then I'd suggest x-tool!
xtool can do more with obd (also renault kia hyundai volvo) and it can change mileage in ecu for fiat alfa lancia opel vw. also airbag crash reset and radio code read.
purpose xtool cant do w204 w212 w221 w207 ..
If you want to start and not spend more money you should buy digiprog, if you want more you can buy xtool later.
Feedback 2:
I have both digiprog and yanhua digimaster. 50% of the cars that digiprog do the digimaster does not especially VW, Audi, Benz.
30% of the cars that digiprog can not do the digimaster does. These cars are French, Italian, Japan, and China cars.
I believe that digimaster is only good for BMW cars that is all.
Not worth to buy at all. Of which waste your money. Digiprog is good for cars 2003-2009 by obd. For VW is the best tool. BENZ is ok does 2007-2009 w212, w204, w221. Audi can handle pretty good mostly a4, a6, a6 2004-2008. Risky a bit on a3.

FAQ: universal odometer correction tool

Up to which year they work with?
U2008 change mileage in the dashboard for the old car prior to 2006 year, Digiprog3 works with the newer cars up to 2012 year, so if you think Tacho universal for 100usd does all what DP3 does and think it waste money, then it is a wrong point. Digimaster 3 also works with newest vehicles.

What vehicles they can work?
U2008, DP3 and D3 all work with a lot of vehicle models. Their difference: DP3 can work with cars, a little part of trucks and motorcycles, such as: ford,
Fiat, vw, Audi, seat, skoda, Merc 203 and 204, bmw CAS, Peugeot, Honda Accord. Digimaster 3 can program mileage for BMW and Mercedes Benz.
Can copy digiprog 3 work with BMW and Mercedes Benz?
No, Digimaster 3 is the best mileage programmer for BMW and Mercedes Benz.

Which one is most powerful?
Digimaster 3 is best quality and most expensive, but it can correct odometer, decode audio, reset airbag (SRS), program ECU and program key (for Mercedes and BMW).
Digiprog3 and tacho universal are mainly used to correct mileage

By what way they correct mileage?

There are three method options to correct mileage: via diagnosis, via chip and via Micro. By which way, all the three tools main unit will prompt the user depends on specific models, at the same time it will display car model appearance, where to remove chip or Micro, what adapter to use and where the chip or Micro locates.
Take digiprog for example, when it corrects mileage for Toyota YARIS C 56, it clearly shows the car model appearance, where to remove chip in the dashboard, what adapter to use and where the dashboard chip locates.

How to update?
Digimaster 3: digimaster3 support sw update online.
Plug the power supply and network cable into digimaster3, click “Management”-“Update”-“Software Upgrade”, then wait it untill the screen display “Upgrade update OK”.

Digiprog 3: it can update, once the newest software is released, if you want to update, send the supplier serial number and they will send you an updating software. Steps: Connect the USB to the computer, start dp3，run Digiloader1.exe; Choose the right port, select Digi1.bin,click the button, then dp3 enter blue screen, if dp3 dose not enter blue screen, check the setting and restart from step 1; wait it process end, if the power supply disconnect, the unit will be damages.
Tacho Pro 2008 can’t update, after power on, don’t select “Update” and donot connect with the computer, otherwise, the screen will display “Reset”.



Src：http://www.mileageprogrammer.com/digiprog-3-or-digimaster-3-you-have-to-read/

Digiprog 3 Smart ForTwo 2007 (BOX/TACHO) Odometer Correction Test

Digiprog 3 and Smart ForTwo 2007 BOX and TACHO. Possible?

Yes. Here you go.

Part 1: Smart ForTwo 2007 BOX

Part 2: Smart ForTwo 2007 TACHO

Part 1: Smart ForTwo 2007 BOX

Requires plug 48:

ST 48

yellow 18 yellow

green 17 green

white 7 white

brown 13 brown

SMART Model 2007 BOX

!!! ALWAYS FOLLOW THE BATTERY !!!

Remove box and disassemble. 

Position of the box: driver footwell left above the steering column. 

Connect the plug 48 with the marked solder points

Attention the big fuses have to be pulled to open the box; Remember slots.

Select the program: car / truck - SMART - FORTWO - BOX.

  

The DIGIPROG 3 indicates the old / wrong KM level.

Program the new / correct KM booth and you're done.

The speedometer must gem. 

Part 2: Smart ForTwo 2007 TACHO

Requires plug 01:

ST 1 clip 3M 923650-08

1 1

2 2

3 3

4 4

19 5

6 6

5 7

7 8

SMART FORTWO 95C640

!!! ALWAYS FOLLOW THE BATTERY !!!

Remove and disassemble the speedometer.

  

Carefully peel off the pointer. 

Locate the chip 95C640

The designation can also be 25LC640.

 ATTENTION: you have to unsolder this chip. 

First, always make a backup of the chip via the EEPROMM program.

Select the program: CAR / TRUCK - SMART FORTWO - CHIP 95C640.

The DIGI PROG displays the old / wrong KM level.

Program the new / correct KM booth and you're done.

The box must gem.

Tech support from http://blog.obdexpress.co.uk/2018/05/22/digiprog-3-smart-fortwo-2007-box-tacho/