How to fix DigiProg 3 Issue "NO CONNECTION"

 

Question: when I tried to use Digiprog 3 mileage programmer to correct mileage for an Audi A4 of the year 2000, a window popped up, saying “NO CONNECTION”. I have also tested it on another A4 of the year 2006, and the error message showed up again. What could be the problem? Is the tool broken? Below is a photo of the problem. Please help. Urgently. Thanks.

Answer:

According to the error message you provide, I guess you are connecting the tool via OBD2 port, right? However, according to the DP3  odometer correction tool manual book, to program mileage for most cars before 2008, you will have to disassemble the dashboard and get access to the mileage chip. Then you will need to use ST01, ST04, or other cables rather than OBD2 cable to clip the chip and let the chip communicate with the Digiprog iii odometer correction tool.

The Digiprog3  will tell you if you need to disassemble the dashboard, as well as which cable you should use to do mileage programming for the car.

Solution: You can disconnect the tool, connect it to your car again, and pay attention to system prompts to determine how to do the programming.

Hope this helps

DigiProg3 Manual: Yamaha YZF R1 2001 Mileage Correction

Hello, guys. I made a small instruction here for you all on how to correct or change the mileage of Yamaha YZF R1 2001 93C46 EEPROM chip using Digiprog 3 odometer programmer

Disclaimer:
The guide is only for educational purposes and not by any means to be wrongly or criminally used for cheating or manipulating with cars mileage for sales purposes

Tool used:
Digiprog 3 v4.94+ ST01/ST04 Cable

Two parts of DigiProg3 Yamaha R1 2001 93C46 mileage correction:

Part 1:

Take apart the EEPROM chip Yamaha YZF-R1 93C46.

You can take a close look at as below:

 

 

In this case, you need the ST04 cable to connect 93C46 EEPROM chip with Digiprog iii.

Fit the chip with ST04 cable clip properly like this:

 

Connect ST04 cable with Digiprog iii and connect device to power supply.

Part 2

The device will power on. You will see an information message, click OK.

Input your device password to enter the main menu.

Go to “MOTORCYCLE” section

Scroll down to select “YAMAHA”, “YZF R1” then “C46 (2001)”.

 

 

It will show “93CS46 PLUG 1”, click OK to continue.

Step 3

You can see the old odometer value as 27584KM.

And just enter a new value like 40000KM, click OK and confirm it again.

Now you change Yamaha R1 mileage successfully using Digiprog iii 

Digiprog 3 V4.94 car list of YAMAHA:

YAMAHA
FAZER
MT03 24C04
TMAX 500 C46
WILD STAR C46
XV 1900 93CS66
YZF R1
C46 2001
C56 2002
L56R 2005
YZF R6 C46

 

Source:http://www.mileageprogrammer.com/digiprog-3-v4-94-yamaha-r1-2001-93c46-odometer-programming/

Citroen Berlingo 2004 BSI mileage correction: succeed

Have a bsi from a Citroen Berlingo 2004 and need to change the mileage in the bsi.
There is one the back 91560.

At first, Digiprog won't read it, keeps saying version unknown.

The correct method is: change mileage manually using Digiprog in EEPROM mode.
Read this article: Digiprog 3 V4.94 program eeprom guide
or Read file and post it on forum for help.

Finally. I managed to sort it..don't think it was soldered on the board correctly.

Besides, obdstar X300M and obdstar dp plus and ODO Master  are confirmed to change mileage on Peugeot & Citroen BSI. This post has details and guide: http://www.mileageprogrammer.com/peugeot-citroen-bsi-mileage-correction/

More:

1. How to use Digiprog 3 to correct odometer on Citroen C5 X7 2011 93C76?

2. How to use Digiprog 3 to correct odometer on Citroen C8 BSI HC12?

Thanks
http://www.mileageprogrammer.com/