How to fix DigiProg 3 Issue "NO CONNECTION"

 

Question: when I tried to use Digiprog 3 mileage programmer to correct mileage for an Audi A4 of the year 2000, a window popped up, saying “NO CONNECTION”. I have also tested it on another A4 of the year 2006, and the error message showed up again. What could be the problem? Is the tool broken? Below is a photo of the problem. Please help. Urgently. Thanks.

Answer:

According to the error message you provide, I guess you are connecting the tool via OBD2 port, right? However, according to the DP3  odometer correction tool manual book, to program mileage for most cars before 2008, you will have to disassemble the dashboard and get access to the mileage chip. Then you will need to use ST01, ST04, or other cables rather than OBD2 cable to clip the chip and let the chip communicate with the Digiprog iii odometer correction tool.

The Digiprog3  will tell you if you need to disassemble the dashboard, as well as which cable you should use to do mileage programming for the car.

Solution: You can disconnect the tool, connect it to your car again, and pay attention to system prompts to determine how to do the programming.

Hope this helps

Digiprog 3 clone OBD change km for VW PASSAT 2004

How-to:change odometer for VW Passat 2004 with Digiprog 3 china clone via OBD
Vehicle: VW Passat 2004
Tool: Digiprog 3
Work: Change mileage from 81km to 1489km
Here is the old mileage:81KM

connect Digiprog 3 to the car via OBD
then the machine starts
select a CAR/TRUCK: VW-PASSAT-PASSATR B5/ B5GP-B5*2004 DIAG-PLUS 16 ,then selet√
DP3 is reading the current mileage

enter a new mileage to change
new mileage: 1489km

Connection...

the mileage on the dash is also changed!

Digiprog 3 china clone is confirmed to OBD change km for VW PASSAT 2004
Works perfectly!

Source:http://www.mileageprogrammer.com/digiprog3-for-vw-passat-2004-odometer-correction/

How to use Digiprog 3 clone for Ferrari 458 odometer correction

Tips and Guides: clone Digiprog 3 Ferrari 458 mileage correction

Possible to change km on Ferrari using Digiprog 3 clone?
I've done a 2010 458 by obd with digiprog.
2min. Done. Perfect
If it reads the correct old mileage you're good to go

Will try 458 with Digiprog 3. Your thoughts?
Once did a 458 with Digiprog 3.
Someone doubt that DP3 can do this. But for me, it works! Though it is a clone, but the software is same as original tool.
The tools only needs to read the EEPROM, we know Digiprog can do this for many other cars without problem, so if it reads the correct mileage so I don’t see much risk.
But the mileage is also in the ECU of Ferrari.

Anyone got experience of China clone Digiprog on Ferrari?
Yes. I did it. Did a Ferrari California with Digiprog 3 in 2min OBD



Which version of digiprog3 did you use? I don't see a selection for Ferrari 458
it was no problem when using digiprog 4.94.
all good.
express bought the tool instead of removing dash. better

Digiprog says it can do over obd, but i have a hard time to believe it does 2012 Ferrari 458. Any professional or official can help confirm this?
Look here:

source: http://www.obdexpress.co.uk/wholesale/main-unit-digiprog3-iii-digiprog-3-odometer-programmer.html
Confirmed! Digiprog 3 Ferrari 458 is supported since version 4.88!

Src:http://www.mileageprogrammer.com/digiprog-3-clone-ferrari-458-odometer-correction/