Which tool can do Toyota prius 2005 dash odomter correction?

 Car model and year: Toyota prius 2005y dash
Purpose: Read and write KM
Toyota Prius 2005 KM reading & writing, digiprog has problem, orange 5 ,Carprog, digimaster 3 are all ok, go on reading for instruction.
Tool to test:

1. digiprog 3: Failed

Using soldering points as it is showing in manual. After reading I got wrong mileage 1114095km...original mileage is 275 000km. but after writing that km which you need, dash shows everything ok in car.

orange 5 programmer + nyo : success
I read it with orange 5 programmer without any problems. Calculated with nyo, as landruiser 93c66. Attached 100% working pinout reading in circuit, maybe someone would be useful this post in the future

3. Carprog full firmware V8.21 : success

Carprog is ok for tis dash--prius 93c66
Change KM Toyota Prius 2006 93C66 for example:
Remove unit from car. Open it and find internal 93C66 EEPROM memory inside.
Use the Carprog A4, A5 or A6(due to situation) EEPROM adapter and change mileage.
In most cases need to remove EEPROM from the board.
Open carprog full software
Select Dashboard->Toyota->Prius->Prius Yazakj 93C66 v0.4

Manually enter mileage you desired


Press Write KM

Write KM success.

4. Yanhua digimaster 3 : success

I recommend Yanhua digimaster 3, it works for Prius 93c66.
Method: it needs to dismantle the dashboard and read the data.
Look at this image: digimaster 3 for prius

Source:http://www.obdexpress.co.uk/upload/pro/digimaster-3-supported-mileage-correction-list.pdf
Edit by Laurance


http://www.mileageprogrammer.com/toyota-prius-2005-km-adjustment-digiprog3/

Citroen c5 x7 2011 93c76 Mileage Adjustment With Digiprog III

Look here: How to use Digiprog iii to do odometer correction for Citroen c5 x7 2011 93c76

Car model: CITROEN C5 TACHO CS 76



Requires plug 01
NOTE: The speedometer and the BSI must be programmed.
(BSI see separate instructions)
C5 speedometer C76
Remove and disassemble the speedometer. Find the chip 93C76 (see picture on the following page). Carefully remove the pointer. You should unsolder this chip. First, always make a backup of the chip via the EEPROMM program.
Select the program: Cars / Trucks - CITROEN - C5 - TACHO C76.
The DIGIPROG indicates the old / wrong KM level.
Program the new / correct KM booth and you're done.
Pictures on the following page

CITROEN C5 TACHO CS 76
Disassemble the defective instrument cluster as described below:


Pictures on the following page:


Digiprog3 tech support is always available at www.obdexpress.co.uk

Source:http://www.mileageprogrammer.com/digiprog3-citroen-c5-x7-2011-93c76/

Peugeot 2008 2017 Mileage Change Via OBD?

Peugeot 2008 2017 odometer correction by OBD,here is some suggestion from cartechnology forum members:

Have one 2017 Peugeot 2008 for odometer correction, I thought I tried to do this obd as its a mobile job at customer house not in workshop. I thought it has the valeo no 3 bsi with eeprom 95320.
Tools I have are:
fvdi 2018
Blue digiprog 3 clone
Green obdstar h108 psa
obdstar x300m

Working tools and method advice:

1. SMOK UHDS with the PSA Module will do it.

In real: expensive and don't have.

2. xtool bsi obd and clocks by epprom adapter only tested

3. I do that model with UPA programmer, in any order but when I connect modules back, I always connect bsi first and then dash.

I dont trust in obd2 tools

4. You can read eeprom by digiprog and export dump to PC if your tool ftdi based ,

Otherwise Post screenshot of area's 0x3a0 and 0x3b0 so we will provide you bytes where need to change
Bsi should be corrected with same value as well , it should be Valeo Bsi with eeprom 95256
Good luck

http://www.mileageprogrammer.com/2017-peugeot-2008-odometer-correction-tool/