Odometer correction 2012 Honda CRV with Digiprog3

Topic: Odometer correction 2012 Honda CRV (has dash 93c76) with Digiprog clone.
PS: With any eeprom programmer you can make the job such as:
Option 1. Digiprog clone: Confirmed
Option 2. upa programmer: Confirmed (costs less than 100 EUR, easy job)

How to do 2012 Honda CRV Odometer correction with Digiprog clone:
This car is edited by eeprom, not obd2. You always have to try to remove eeprom from dash for a better reading, use EEPROM MODE in Digiprog, select 93c76 x 16 bits and read it, verify it, and save the original file read, then post your file here with exact original mileage and mileage you need and I will edit for you.
[caption id="attachment_3847" align="aligncenter" width="1000"] Eeprom 01[/caption]

Test signal continuity between bdm ponits marked in the picture and the legs eeprom
Use pin 1,2,3,4,5 and 8 only from eeprom
[caption id="attachment_3848" align="aligncenter" width="1000"] Eeprom 02[/caption]

Use thin wires to join the colors from adapter to eeprom legs.
[caption id="attachment_3849" align="aligncenter" width="1000"] Eeprom 03[/caption]

Open your db25 adapter and check it
connect like this picture
[caption id="attachment_3850" align="aligncenter" width="324"] Wiring Diagram 04[/caption]
In general, Digiprog clone is a good tool if you know how to use it well.... I think principal problem is you dont have any experience in this job and you need a good supporter who can teach you this job.
http://www.obdexpress.co.uk

Source:http://www.mileageprogrammer.com/2012-honda-crv-odometer-correction-with-digiprog-clone/

Citroen Berlingo 2004 BSI mileage correction: succeed

Have a bsi from a Citroen Berlingo 2004 and need to change the mileage in the bsi.
There is one the back 91560.

At first, Digiprog won't read it, keeps saying version unknown.

The correct method is: change mileage manually using Digiprog in EEPROM mode.
Read this article: Digiprog 3 V4.94 program eeprom guide
or Read file and post it on forum for help.

Finally. I managed to sort it..don't think it was soldered on the board correctly.

Besides, obdstar X300M and obdstar dp plus and ODO Master  are confirmed to change mileage on Peugeot & Citroen BSI. This post has details and guide: http://www.mileageprogrammer.com/peugeot-citroen-bsi-mileage-correction/

More:

1. How to use Digiprog 3 to correct odometer on Citroen C5 X7 2011 93C76?

2. How to use Digiprog 3 to correct odometer on Citroen C8 BSI HC12?

Thanks
http://www.mileageprogrammer.com/

Digimaster 3 doesn’t need tokens since Sept, 2018

Good news!!! Since September, 2018, Yanhua Digimaster 3 doesn’t consume the tokens any more, the machine comes with 200 tokens for the coming updates. If your Digimaster 3 was bought before September, 2018, it still needs to consume tokens.

Question:

Does Digimaster 3 need tokens for kia picanto ion 2016-2018?

When I wanted to upgrade module “ID 063f”, the system prompted “50 tokens are needed”.

Answer: that means your machine was bought before 09-12-2018, and need 50 tokens.

Usually, the dealer supply 200 tokens or 300 tokens.

200 tokens package:

http://www.obdexpress.co.uk/wholesale/buy-300-token-digimaster-3-ckm100-get-cas4-authorize.html

300 tokens package:

http://www.obdexpress.co.uk/wholesale/300-tokens-for-digimaster-3-ckm100-ckm200-get-free-digiprog-3.html

Source：http://www.mileageprogrammer.com/digimaster-iii-doesnt-need-tokens-since-sept-2018/

DIGIMASTER III Update To V1.8.1908.05

Digimaster III Version: 1.8.1908.05 update on 28,August. 2019:
Here is the details :
Language: Chinese, English
Update method: update online lifetime for free
New added car model for Airbag resetting
Mitsubishi P8635A207
Citroen C5-9810155880
Honda 77960-T9A-P820-M1
Honda 77960-T4N-H711-M1
Honda 77960-TS6-H711-M1
Honda 77960-T4D-H710-M1
Honda 77960-T6P-S610-M1
Honda 77960-T6P-H420-M1
Suzuki 38910-62L00
Honda 77960-T2A-H720-M1
New added car model for odometer adjustment:
Kubota Tractor 93c56
Casece Harvester 93C46
Suzuki vitara 93C86
New added adapter
Universal pin detect adapter
http://www.mileageprogrammer.com/

Digiprog 3 clone OBD change km for VW PASSAT 2004

How-to:change odometer for VW Passat 2004 with Digiprog 3 china clone via OBD
Vehicle: VW Passat 2004
Tool: Digiprog 3
Work: Change mileage from 81km to 1489km
Here is the old mileage:81KM

connect Digiprog 3 to the car via OBD
then the machine starts
select a CAR/TRUCK: VW-PASSAT-PASSATR B5/ B5GP-B5*2004 DIAG-PLUS 16 ,then selet√
DP3 is reading the current mileage

enter a new mileage to change
new mileage: 1489km

Connection...

the mileage on the dash is also changed!

Digiprog 3 china clone is confirmed to OBD change km for VW PASSAT 2004
Works perfectly!

Source:http://www.mileageprogrammer.com/digiprog3-for-vw-passat-2004-odometer-correction/

OBD2 odometer correction Tool Buying advice

Experience with OBD2 solution for odometer correction on all makes at cheap & expensive price.

Cheap working ones:

1. obdstar x300m

- via OBD2

- obdstar x300m price drops to 209eur. And it can do what you paid.

- obdstar x300m reviews (during the past 6 months)
http://blog.obdexpress.co.uk/2019/08/09/obdstar-x300m-price-drops/
OBDSTAR DP Plus mileage correction feedback (from 7th October, 2015 to now and future)
https://www.digital-kaos.co.uk/forums/showthread.php/491145-OBDSTAR-Mileage-Correction-Feedback/

- Free download: obdstar x300m vehicle coverage

2. Clone digiprog 3 4.94

- Method: besides via OBD, it allows the user to change KM via Chip, Cluster & BCM, Tacho & BSI, Micro, EWS, etc.

- digiprog 3 4.94 coverage:
http://www.mileageprogrammer.com/digiprog-3-vs-obdstar-x300m-mileage-programmer/

- digiprog 3 4.94 reviews
http://blog.obdexpress.co.uk/2017/09/22/digiprog3-v4-94-mileage-correction-car-list/

Less expensive one:
OBDSTAR DP Plus is a full OBD2 solution for odometer correction on all makes. Go to the official site http://en.obdstar.com/Function%20List.html you are able to view the vehicle list.

Expensive ones:

1. Enigma is probably the best on the long run

2. DP4 its the best for this job diagpro4  but very expensive

Read article: DP4 or DP3, which one better

Conclusion:
Problem will start if you have only 1 tool and this fails. And if it damage the dash for example on VAG you will have problems with immo and keys too and each fail will cost you much time and most time money too.
You will need good programmer too to fix dashes if anything happens.
Just my opinion - buy some tools just for 1 brand and good programmer to start to work or better play at beginning.


 Source:http://www.mileageprogrammer.com/need-universal-obd2-odometer-correction-tool/

Which tool can do Toyota prius 2005 dash odomter correction?

 Car model and year: Toyota prius 2005y dash
Purpose: Read and write KM
Toyota Prius 2005 KM reading & writing, digiprog has problem, orange 5 ,Carprog, digimaster 3 are all ok, go on reading for instruction.
Tool to test:

1. digiprog 3: Failed

Using soldering points as it is showing in manual. After reading I got wrong mileage 1114095km...original mileage is 275 000km. but after writing that km which you need, dash shows everything ok in car.

orange 5 programmer + nyo : success
I read it with orange 5 programmer without any problems. Calculated with nyo, as landruiser 93c66. Attached 100% working pinout reading in circuit, maybe someone would be useful this post in the future

3. Carprog full firmware V8.21 : success

Carprog is ok for tis dash--prius 93c66
Change KM Toyota Prius 2006 93C66 for example:
Remove unit from car. Open it and find internal 93C66 EEPROM memory inside.
Use the Carprog A4, A5 or A6(due to situation) EEPROM adapter and change mileage.
In most cases need to remove EEPROM from the board.
Open carprog full software
Select Dashboard->Toyota->Prius->Prius Yazakj 93C66 v0.4

Manually enter mileage you desired


Press Write KM

Write KM success.

4. Yanhua digimaster 3 : success

I recommend Yanhua digimaster 3, it works for Prius 93c66.
Method: it needs to dismantle the dashboard and read the data.
Look at this image: digimaster 3 for prius

Source:http://www.obdexpress.co.uk/upload/pro/digimaster-3-supported-mileage-correction-list.pdf
Edit by Laurance


http://www.mileageprogrammer.com/toyota-prius-2005-km-adjustment-digiprog3/

Citroen c5 x7 2011 93c76 Mileage Adjustment With Digiprog III

Look here: How to use Digiprog iii to do odometer correction for Citroen c5 x7 2011 93c76

Car model: CITROEN C5 TACHO CS 76



Requires plug 01
NOTE: The speedometer and the BSI must be programmed.
(BSI see separate instructions)
C5 speedometer C76
Remove and disassemble the speedometer. Find the chip 93C76 (see picture on the following page). Carefully remove the pointer. You should unsolder this chip. First, always make a backup of the chip via the EEPROMM program.
Select the program: Cars / Trucks - CITROEN - C5 - TACHO C76.
The DIGIPROG indicates the old / wrong KM level.
Program the new / correct KM booth and you're done.
Pictures on the following page

CITROEN C5 TACHO CS 76
Disassemble the defective instrument cluster as described below:


Pictures on the following page:


Digiprog3 tech support is always available at www.obdexpress.co.uk

Source:http://www.mileageprogrammer.com/digiprog3-citroen-c5-x7-2011-93c76/

Peugeot 2008 2017 Mileage Change Via OBD?

Peugeot 2008 2017 odometer correction by OBD,here is some suggestion from cartechnology forum members:

Have one 2017 Peugeot 2008 for odometer correction, I thought I tried to do this obd as its a mobile job at customer house not in workshop. I thought it has the valeo no 3 bsi with eeprom 95320.
Tools I have are:
fvdi 2018
Blue digiprog 3 clone
Green obdstar h108 psa
obdstar x300m

Working tools and method advice:

1. SMOK UHDS with the PSA Module will do it.

In real: expensive and don't have.

2. xtool bsi obd and clocks by epprom adapter only tested

3. I do that model with UPA programmer, in any order but when I connect modules back, I always connect bsi first and then dash.

I dont trust in obd2 tools

4. You can read eeprom by digiprog and export dump to PC if your tool ftdi based ,

Otherwise Post screenshot of area's 0x3a0 and 0x3b0 so we will provide you bytes where need to change
Bsi should be corrected with same value as well , it should be Valeo Bsi with eeprom 95256
Good luck

http://www.mileageprogrammer.com/2017-peugeot-2008-odometer-correction-tool/

How does Digimaster 3 correct odometer via OBP adapter (IC soldering)?

When using Digimaster 3 to adjust mileage, one method is through the OBP adapter, which means the IC chip needs to be removed from the cluster, then solder on the OBP adapter, meanwhile the D3 is connected to the OBP adapter to correct odometer, then solder the IC chip back to the dashboard.

1. Desolder the IC chip from the dashboard.

2. Clear the excess tin from the IC.

3. Solder the IC into the OBP adapter which is connected to digimaster 3.

Read the original mileage value, then input the new value you want.

4. Then desolder the IC chip from the OBP adapter.

5. Solder the IC into the dashboard again.

6. Use the Banana oil to clear the IC which is soldered back into the dashboard.

7. Job is done.

Video demo:Digimaster 3: IC Soldering



http://www.mileageprogrammer.com/digimaster-3-ic-soldering/

Digimaster III added Honda Motor for odometer adjustment

Digimaster III New added car models for odometer adjustment and Airbag reset in 2019:
[Mar.28th.2019]
Newly added car for airbag resetting
Mitsubishi P8635A248
Mitsubishi P8635A251
Mitsubishi P8635A206
Newly added car model for odometer adjustment
Honda Motor CBR1000
SUZUKI Motor 93C66

[Feb.27th.2019]
Newly added car for airbag resetting
Suzuki 38910-59J71-000
MG_Rover 10003952-01
Infiniti 988201WW2A
[Jan.30th.2019]
Newly added car for airbag resetting
Toyota 4700-89170-60330
Toyota RAV4-89170-42630
Toyota 89170-08080
Toyota FJ-CRUISE 89170-35270
Toyota 89170-02B00
SSanyong Rexton 89250-08121
Newly added car for odometer adjustment
Honda 2018 CRV
To be continued...

http://www.mileageprogrammer.com/digimaster-iii-free-update-in-2019/