Digiprog3/Xprog/Carprog read&write Audi A4 eeprom HC12 mileage

Topic :how to use Digiprog3/Xprog/Carprog read&write Audi A4 eeprom HC12 mileage

Here you are:

Purpose:

copy the immo information from a cluster to another
make the mileage follow with the immo information

Model:

Audi a4 2001

Optional devices:

Digiprog3, or ecu programmers like Xprog, Carprog, UPA-USB programmer

Original cluster:

The Jaeger cluster barely works

  

Suggestion:

read the pin code from both the Instrument and adapt it to the vehicle

What to do on pin 21 and 22 on the chip:

 

- With ECU programmers:

Eprom.set type,mcu,hc12,read,save.
eprom,set type,mcu,hc12,file,load,write.
Buy yourself Xprog-M programmer, Carprog, UPA-USB.
Pin 21 and 22 jumper after programming or wait 10 minutes.

- with Digiprog3:

 

Eprom,set type,mcu,hc12,read,save.
eprom,set type,mcu,hc12,file,load,write.

Reference:

Eeprom HC12 read and write to the other counter:

AUDI MM AB 8/2001 DIAGNOSIS / TACHO DIAGNOSIS

(Write down the exact ALWAYS old / incorrect Mileage)

The diagnostic port is in the driver's footwell. Turn the ignition

on a vehicle. Connect plug ST16 the diagnostic port and the

DIGIPROG.

Select the program: cars / trucks - AUDI - MM 4 / 99- DIAG.

The DIGI PROG II shows you the old / incorrect Mileage.

Enter the new / correct Mileage and confirm this.

Should be then after programming on the speedometer 999999 KM give

The old / wrong KM value again so that the speedometer again the old /

false indicates KM. Now you build the speedometer and break it to the

see board. Solder the green and black wire to the same color marked

Arrows at. Now connect the blue and the green plug with

the speedometer and plug ST41 with the DIGI PROG (picture on the following page.)

Now select the program: cars / trucks - AUDI - MM 4/99 HC12.

The DIGI PROG shows you the old / incorrect Mileage. Enter the

new / correct Mileage and confirm this with the hook.

Now shows you the DigiProg II 5 min wait. Remove the connection

between the DigiProg and the speedometer, wait 5 minutes and build the speedometer

again. Alternatively, for 5 min. Wait, you can also like in the image on the

next page shows the pins 21 and 22 bridges.

Here necessarily the board from any power supply (Digiprog,

external power supply, etc.), Pin 21 + 22 bridge, and then you can use the tachometer

Immediately reinstall.

OBDexpress disclaimer:

TRY ON YOUR OWN RISK

Thanks for all tech support from members’ share at http://cartechnology.co.uk/

http://www.mileageprogrammer.com/readwrite-audi-a4-eeprom-hc12-mileage/

How to change mileage for Ford Mondeo using Digiprog 3

Confirmed! Digiprog 3 can correct the mileage on a Ford Mondeo through OBD.
Connect the DP3 unit to the car thru the OBD port

Power on
 
Enter password

In the DP3 main menu, select CAR/TRUCK

Select FORD MONDEO DIAG 2008
         
Current odometer: 189237km
 
Go for odometer correction
 

Enter new KM: 183000
   
New KM displayed on the dashboard
Digiprog 3 changed KM successfully.
Job’s done!
Other options for Ford odometer correction:
Obdstar F100:
Designed for Ford/Mazda odometer correction and key programming
Obdstar H100:
Esp. for Ford/Mazda 2017-2018 models dometer correction and key programming
Obdstar X300M:
Good universal odometer correction tool, covering Ford and AUDI/VW/SKODA/SEAT, BENTLEY, BENZ, BESTURN, CHRYSLER(CHRYSLER/DODGE/JEEP), CITROEN, FIAT, GEELY, GM(BUICK/CADILLAC/CHEVROLET/HUMMER), GMC, GREATWALL, HYUNDAI, INFINITI, JAGUAR, KIA, LANDROVER, MAZDA, MITSUBISHI, NISSAN, OPEL, PEUGEOT, PORSCHE, PONTIAC, PROTON, RENAULT, ROEWE, SATURN, SMART, SSANGYONG, VOLVO etc.

Source:
http://www.mileageprogrammer.com/digiprog-3-odometer-correction-ford-mondeo-via-obd/